Yamaha Counter shaft Nut

Fits RD 250.350,400, R5, DS7 1970-1979

CLICK HERE

Fits RD 250.350,400, R5, DS7 1970-1979

$8.99 (90507-25023)

• Genuine Yamaha Part

• Comes as pictures with mounting gasket (not shown)

• Two outlet (only one shown)

• Three position, ON / OFF / RESERVE

Click Here

HVC Reproduction Caliper Piston

• Made from stainless steel so they will never pit and rust around the seals again

• 42.8mmOD  x 33.05mm tall

• If you are not satisfied with our pistons we will offer a full refund.

• Highest quality with the best price.

• MADE IN THE USA!!

$24.75ea (HVC200106F)

• Reproduction Carburetor boots

• Sold as a set of two

• boots mount on carburetor tops  for the RD400F Daytona.

$34.99 (HVC200115)

• Replace your old or missing neutral wire isolator

• Located under the L/H engine side cover

• Applications

  • Fits all Yamaha 2 stroke twins 1970-1979,

  • Yamaha RZ 84-85

$3.50 (HVC200116)

• Reproduction Engine mount dampers

• Contains the following dampers, 8 total

  • 1A1-15316-00-00 (4)

  • 1A1-15326-00-00 (2)

  • 1A1-15336-00-00 (2)

$135.99 (MK256)

Includes Spring, Ball Washer and Retainer Clip

Applications

• R5, DS7

• RD250/350/400 1973-1979

• Other Early Model Yamahas

• HVC Billet Aluminum Kick Starter

$ 9.99 (HVC20046A)

• Made from 304 Stainless Steel
• Fits Yamaha RD 400

$4.50 (1A0-22149-00-00)

The Clutch push rod wears over time creating a leak around the seal. The push rod is no longer available from Yamaha.  Replace your worn or bent push rod with A HVC reproduction push rod.  Made to exact factory specs.

$12.99 (328-16357-00-00)

Application

RD250/350(237-16357-01-00)R5/DS7 (237-16357-01-00)RD400/250 76-79(328-16357-00-00)

• HVC Reproduction Item
• Fits into the left side cover
• Replace your hard dried out guide with our new guide.
• Fits Yamaha R5, DS7,RD350, RD400

$9.00 (HVC200118)

• HVC Signature Item
• Block off the gap when you remove the oil injection pump and hoses
• Fits into the left side cover.
• Fits Yamaha R5, DS7,RD350, RD400

$9.00  (HVC200118-1)

Yamaha Chain Tensioner Bolt Set

Replacement Chain Tensioner

Includes: Two - 8 x 1.25 x 5mm bolts with a 10mm head
and
Two-8 x 1.25 nuts 12mm wrench

Two Bolt Sets Per Package

$5.99 (HVC200121)

 

This is the oil tank hose that attaches to the bottom of the oil tank and runs to the oil injection pump. The line is the correct size for the side cover grommet.

• DS7/R5 70-72

• RD250/350 73-75

• RD250/400 76-79

$10.99 (90445-09122-00)

Contains All new grommets and hardware for the speedometer and tachometer to be mounted  in the bucket and on to the motorcycle.

$33.50 (HVC200123)

Attaches to the rear fender to dampen the rear grab bar

Replaces Yamaha Part Numbers 341-216380-00-00 and 1A2-21638-00-00

$7.99 (341-21638-00-00)