 |
 |
 |
 |
Blank Plate |
RD250/350 1973-1975 Ignition trim plate
$39.99 (HVC20087-9)
HVC reproduction item. Laser cut from .020
aluminum, anodized black and laser etched.
Over time the original ignition trim plate
will fade to a brown color from the sun or get scratched up from
keys rubbing against it. Replace your old ugly trim plate with our
new reproduction plate.
Easy to install! Remove the old trim
plate and bond to the gauge cluster with a nonporous adhesive or
purchase our easy to use 1 oz tube of adhesive.
Pliobond Adhesive 1oz tube
$3.99 (Pliobond 20 1oz)
|
RD250/350 1973-1975 Blank ignition trim plate
$21.99 (HVC20087-10)
HVC reproduction item. Laser cut from .020
aluminum, anodized black
Want to customize your gauge cluster?
Use this blank trim plate.
Easy to install! Remove the old trim
plate and bond to the gauge cluster with a nonporous adhesive or
purchase our easy to use 1 oz tube of adhesive.
Pliobond Adhesive 1oz tube
$3.99 (Pliobond 20 1oz)
|
Generator Rotor Woodruff
key
4mm X 13mm
Left hand side crank shaft to
generator rotor woodruff key
OEM Yamaha Part
$6.99 (90280-04005)
|
|
Oil Injection Pump
Block Off Plate
-
Use this kit when you
remove the oil injection pump to run Pre-mix.
-
Block off plate is made
from 0.080 inch aluminum that has been laser cut to the exact
size of the oil pump mating surface.
-
Includes the Plate and a
gasket.
$9.99 (HVC200111)
|
Clutch Push Rod
The Clutch push rod wears over time creating a
leak around the seal. The push rod is no longer available from Yamaha.
Replace your worn or bent push rod with a HVC reproduction push rod.
Made to exact factory specs.
Applications
- Length 215mm RD, R5, DS7 1970-1975
$12.99 (237-16357-01-00)
|
Yamaha RD Seat Rubber Pad
Kit
$14.99 (HVC200110)
|
|
Yamaha Counter Shaft Nut
Fits RD 250.350,400, R5, DS7
1970-1979
CLICK
HERE
|
Side Stand Spring
Fits RD 250.350,400, R5, DS7
1970-1979
$8.99 (90507-25023)
|
Footrest Bracket Damper
Set
-
R5, DS7, RD250, RD350, RD400
-
HVCcycle reproduction part
-
No longer available from Yamaha
-
Set of four, to mount one foot
peg bracket
$34.99 (278-27414-01-00)
|
Air Box Cover
Strap 1970-1975
-
Very rarely do you find an
RD or R5 with the stock air box cover strap in place. Finally a
solution, HVC's simple but effective strap will secure the air box
cover in place.
-
Replacement for Yamaha Part
Number 278-14459-00-00
$14.99 (HVC200114)
|
|
Sprocket Bolt Lock Washers
|
Neutral Wire Isolator
$3.50 (HVC200116)
|
Fuel Cap Internal Seals
HVCcycle Reproduction parts
The Fuel tank cap seal on the Yamaha RD250's
and 350's have two internal seals that prevent fuel from spilling over
out of the tank. These two seals have not been available from
Yamaha for years. Now you can protect your paint and tank once again
with our reproduction seals.
Sold as a set
$14.99 (HVC20064A)
External cap Seal available, Click here |
|
Yamaha Kick Starter Kit
Includes Spring, Ball Washer and Retainer
Clip
Applications
$ 9.99 (HVC20046A)
|
Oil Injection Line
Guide
- HVC Reproduction Item
- Fits into the left side cover
- Replace your hard dried out guide with
our new guide.
- Fits Yamaha R5, DS7,RD350, RD400
$9.00 (HVC200118)
|
Oil Injection Line Block
Off Plug
- HVC Signature Item
- Block off the gap when you remove the
oil injection pump and hoses
- Fits into the left side cover.
- Fits Yamaha R5, DS7,RD350, RD400
$9.00 (HVC200118-1)
|
Yamaha 250, 350, 400
Shift Shaft
Reproduction Shift Shaft.
Applications
Includes
$69.99 (278-18101-01-00) |
|
Oil Tank Hose
This is the oil tank hose that attaches to the
bottom of the oil tank and runs to the oil injection pump. The line is
the correct size for the side cover grommet.
Fits the following
|
Yamaha RD / R5 Clutch
Cable Retainer
HVCcycle Reproduction Item
- No longer available from Yamaha
- OEM Part number 278-15441-00-00
- Made from 6063 Billet Aluminum
- Fits Yamaha R5 / DS7 1970-1972, RD250 &
350
- Fits on top of the Left side cover to
support the clutch cable
$17.99 (HVC200119)
|
Yamaha Chain Tensioner
Bolt Set
Replacement Chain Tensioner
Includes: Two - 8 x 1.25 x 5mm bolts with a
10mm head
and
Two-8 x 1.25 nuts 12mm wrench
Two Bolt Sets Per Package
$5.99 (HVC200121)
|
Side Cover / Oil Tank
Mold Kit
Includes the left and right mold.
OEM Part Numbers
- 360-21781-00-00
- 360-21782-00-00
$60.00 (HVC200122) |
|
|
|
|
|
