4mm X 13mm

Left hand side crank shaft   to generator rotor     woodruff key

OEM Yamaha Part

$6.99 (90280-04005)

• Use this kit when you remove the oil injection pump to run Pre-mix.

• Block off plate is made from 0.080 inch aluminum that has been laser cut to the exact size of the oil pump mating surface.

• Includes the Plate and a gasket.

$9.99 (HVC200111)

Includes 5 Rubber Bumpers

Fits RD400 1976-1978

$24.99 (HVC200120)

$5.99 (583-15371-00-00)

Yamaha Counter shaft Nut

Fits RD 250.350,400, R5, DS7 1970-1979

CLICK HERE

Fits RD 250.350,400, R5, DS7 1970-1979

$13.99 (90507-25023)

• RD400 (shaped different than the original, Fits the same)

• HVCcycle reproduction part

• No longer available from Yamaha

• Set of four, to mount one foot peg bracket

$34.99 (278-27414-01-00)

• Genuine Yamaha Part

• Comes as pictures with mounting gasket (not shown)

• Two outlet (only one shown)

• Three position, ON / OFF / RESERVE

Click Here

The Clutch push rod wears over time creating a leak around the seal. The push rod is no longer available from Yamaha.  Replace your worn or bent push rod with A HVC reproduction push rod.  Made to exact factory specs.

$16.99 (328-16357-00-00)

Application

RD250/350(237-16357-01-00)R5/DS7 (237-16357-01-00)RD400/250 76-79(328-16357-00-00)

• Sold as a set of two

$10.99 (002-452)

• Replace your old or missing neutral wire isolator

• Located under the L/H engine side cover

• Applications

  • Fits all Yamaha 2 stroke twins 1970-1979,

  • Yamaha RZ 84-85

$3.50 (HVC200116)

Reproduction Shift Shaft.

Applications

• Yamaha R5, DS7 1970-1972

• Yamaha RD250, RD350 1973-1975

• Yamaha RD400 1976-1978

Includes

• Shifter shaft

$69.99 (278-18101-01-00)

• Reproduction Engine mount dampers

• Contains the following dampers, 8 total

  • 1A1-15316-00-00 (4)

  • 1A1-15326-00-00 (2)

  • 1A1-15336-00-00 (2)

$135.99 (MK256)

Includes Spring, Ball Washer and Retainer Clip

Applications

• R5, DS7

• RD250/350/400 1973-1979

• Other Early Model Yamahas

• HVC Billet Aluminum Kick Starter

$ 9.99 (HVC20046A)

• HVC Reproduction Item
• Fits into the left side cover
• Replace your hard dried out guide with our new guide.
• Fits Yamaha R5, DS7,RD350, RD400

$9.00 (HVC200118)

• HVC Signature Item
• Block off the gap when you remove the oil injection pump and hoses
• Fits into the left side cover.
• Fits Yamaha R5, DS7,RD350, RD400

$9.00  (HVC200118-1)

• Made from 304 Stainless Steel
• Fits Yamaha RD 400

$4.50 (1A0-22149-00-00)

Contains All new grommets and hardware for the speedometer and tachometer to be mounted  in the bucket and on to the motorcycle.

$33.50 (HVC200123)

Attaches to the rear fender to dampen the rear grab bar

Replaces Yamaha Part Numbers 341-216380-00-00 and 1A2-21638-00-00

$7.99 (341-21638-00-00)

$15.99 (521-11161-01-00)

$34.99(1A0-11162-02-00)

Replacement Chain Tensioner

Includes: Two - 8 x 1.25 x 5mm bolts with a 10mm head
and
Two-8 x 1.25 nuts 12mm wrench

Two Bolt Sets Per Package

$5.99 (HVC200121)

 

• Reproduction locking fuel cap assembly

• Includes the seal and vent assembly and 2 keys

• Applications

  • RD400 1976-1978, 1A0-24602-00-00

  • RD125DX  1E7-24602-00-00

  $43.50 (HVC200127)

  

• Reproduction dampers, exact copy of the original Yamaha dampers

• Made from high quality fuel and heat resistant rubber

• Dampers are used to secure the battery box.

• Applications

  • Yamaha RD400 1977-1980

• Sold as a set of 2

$12.99 (1A0-21746-01-00)

• Reproduction Plate, exact copy of the original Yamaha part

• Made from 14 Gauge Steel

• Applications

  • 1973-1975 Yamaha RD250/ RD350 A/B

  • 1976-1980 Yamaha RD400 C/D/E/F/G

  • 1976-1980 Yamaha TZ250/TZ350 C/D/E/F/G

$9.99 (360-17471-00-00)