|
|
|
Motion Pro 2-Stroke Timing Kit
| Includes dial
indicator with extensions and a 14mm spark plug thread adapter.
Allows inspection and adjustment of ignition timing. Gauge
face size is 1 1/2". For water cooled engines. |
$129.95 (3801-0030)
|
 Motion
Pro 2-Stroke Timing Adapter
kit for air cooled engines
Includes an extended thread adapter and dial
indicator extension. Allows Water Cooled Kit to be used on air
cooled engines.
$11.95 (3801-0029)
|
|
Soft
Tie Extensions
If you’ve got to tie your bike
down, this is the best protection for expensive paint and chrome. Loop
this one-inch nylon webbing around your handlebars, fork braces, or rear
seat rails and insert a tie down hook—metal-to-metal contact is
completely eliminated. Rated at 1200 lbs breaking strength with a 400
lb. working load capacity per strap. Pair of two. 12-inch length.
$5.95
(13-0002)
|
Terminal Crimper Tool
For B-series Terminals
$26.95 (93150)
|
|
Spring Installation tool
-
T-handle spring puller
provides a secure, comfortable grip for maximum leverage
-
Allows mechanics to remove
exhaust springs in seconds
$6.95
(FMF011231)
|
2-Stroke Leak-Down Tester
- Designed to check for air leaks in
2-stroke engines
- Includes air pressure gauge, pump-up
bulb and most fittings and adapters for single- and twin-cylinder
2-stroke motorcycle engines
- Packed in a convenient carry box,
complete with instructions
- Made in the U.S.A.
- This is the tool we use at HVCcycle.
$308.95 (P538) |
|
Yamaha RD Axle Wrench
-
This is a copy of the axle
wrench that was supplied in the original tool kit. 22mm & 29mm
-
Makes loosening and
tightening the double nut on the axle easy without interfering with
the exhaust.
-
Made from hardened tool
steel and zinc plated.
-
Works on the following
-
Yamaha R5 and DS7
-
Yamaha RD250 and 350
-
Yamaha RD400, 1976-1978
$17.99
(HVC200124)
|
Mikuni
Service Tool Kit
Handy kit includes all tools necessary to completely
disassemble Mikuni carbs, change jets, etc.
$11.95
(12-1866) |
|
Flex Hone
Available in many sizes other than listed.
Listed are the sizes that work the best on the Yamaha
2-stroke twins
|
|
Fly Wheel Rotor
Puller |
 |
|
|
|
$4.50 (HVC200136)
|
|
Cable Luber
- Used to inject lubricant into cable
housing
- Clamps over housing and wire allowing an
aerosol can to be connected
- Once lube runs out the far end, the
cable is lubricated
|
4 Stroke Leak Down Tester
-
Designed to check the
amount of cylinder leakage in a 4-stroke engine
-
With air pressure of
70-160 psi, this system will pressurize the cylinder
with 60 psi of air
-
Gauge will register the
total percentage of leakage past the rings, head gasket,
intake & exhaust valves
-
10, 12, 14mm spark plug
thread hoses, regulator and gauge included
-
Speeds up
troubleshooting and helps to isolate bad components
-
Included convenient
carrying box & Instructions
|
$160.95 (MP08-126) |
|
Ignition Timing Tester "Buzzbox"
Eliminates the guesswork when timing a
points-type ignition. Allows you to concentrate on adjusting the points
without having to look at your multi-meter for a reading, just listen for
the audible tone to know when your points close. A switch allows for either
a light or a tone at the moment of point closure Can also be used as a
continuity tester.
$41.95 (LM4100)
|
HVCcycle ASS
FAULT Protector
- Park your bike on the grass, dirt
or HOT asphalt.
- For use under the side stand.
- Made from 14 gauge Stainless Steel,
will not rust
- Will support any size motorcycle
$5.99(ASS Fault Protector)
|
MOTION PRO CLUTCH TOOL
Designed to hold clutch baskets, flywheels, gears,
sprockets, etc. Jaws open to 5 inches wide. Made of medium carbon
steel with hardened jaws. A very useful tool for holding any kind of
mechanical work.
$24.95 (P518) |
PISTON PIN PULLER
Universal Piston Pin Puller easily removes all sizes of piston
pins without any damage to pistons.
$28.95 (865)
|
